Domino Sim2 Bedienungsanleitung

D10MultimediaUser's Manualwww.sim2.comwww.sim2.comDownloaded From projector-manual.com Sim2 Manuals

D1010Rear PortsDVI-D5HDMI6USBREMOTE TRIG 1GRAPHIC RGB RS-2324VIDEOYPrPb31S-VIDEOPOWER 100/240 V2iteM labeldeScriptiOn1 DVI-D Connect the computer cabl

11D10Bottom ViewiteM label deScriptiOn1Ceiling support holesContact your dealer for information on mounting the projector on a ceiling2Height adjuster

D1012Remote Control Functionslabel deScriptiOn On I Turns projector power onl21 3AspectPowerModeColor TempGAMMALIGHTBLANKAUTO54 6EXITMENUENTERUSER

13D10Remote Control Operating RangeThe remote control uses infrared transmission to control the projector. It is not necessary to point the remote dir

D10142. Setup and OperatiOnInserting the Remote Control Batteries1. Remove the battery compart-ment cover by sliding the cover in the direction of the

15D10Connecting Input DevicesA PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices incl

D1016Starting and Shutting down the Projector1. Remove the lens cover.2. Connect the power cord to the projector. Connect the other end to a wall outl

17D10Adjusting the Projector LevelTake note of the following when setting up the projector:• The projector table or stand should be level and sturdy.

D1018Adjusting the Focus and Zoom1. L o c a t e t h e i m a g e z o o m an d f o c u s adjustment rings on the projector.Focus Zoom2. Use

19D103. On-Screen diSplay (OSd) Menu SettinGSOSD Menu ControlsThe projector has an OSD that lets you make image adjustments and change various setting

SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - ITALYPhone +39.0434.383.256 • Fax +39.0434.383.260www.sim2.com • e-mail: info@si

D1020Setting the OSD LanguageYou may want to reference the OSD on your projector while reading this section. Set the OSD language to your preference b

21D10OSD Menu OverviewUse the following illustration to quickly nd a setting or determine the range for a setting. (1) None *(2)(3)(4) VerticalRamp(5

D1022Image Menu Press the Menu button to open the OSD menu. Press the cursor ◄ ► button to move to the Image menu. Press the cursor ▲▼ button to move

23D10iteM deScriptiOn defaultAuto source selectionPress the cursor ◄ ► button to enable auto source selection. OFFSource selectPress the cursor butto

D1024OSD menu Functions Available for Connected SourcefunctiOn rGb dVi hdMicOMpOnent VideOcOMpOSite VideOS-VideO rGbSBrightness x x x x x x xContrast

25D10OptionsPress the Menu button to open the OSD menu. Press the cursor ◄ ► button to move to the Options menu. Press the cursor ▲▼ button to move up

D1026iteM deScriptiOn defaultBrilliant colorPress the cursor ◄ ► button to set brilliant color On or Off.(Range: ON – OFF) Brilliant Color Technology

27D10Settings Menu Press the Menu button to open the OSD menu. Press the cursor ◄ ► button to move to the Settings menu. Press the cursor ▲▼ button to

D1028iteM deScriptiOn defaultPhasePress the cursor ◄ ► button to adjust the A/D sampling clock. (Range: 0 - 100)50FrequencyPress the cursor ◄ ► button

29D10User Color Menu Press the Menu button to open the OSD menu. Press the cursor ◄ ► button to move to the Picture menu. Press the cursor ▲▼ button t

Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights re

D1030Info Menu Press the Menu button to open the OSD menu. Press the cursor ◄ ► button to move to the Info menu. Press the cursor ▲▼ button to move up

31D104. Maintenance and SecurityReplacing the Projection LampSim2 recommends changing the projection lamp after a warning message displays Warning: La

D10323.Remove the three screws from the lamp module.4.Lift the module handle up.5. Pull rmly on the module handle to remove the lamp module.6. Revers

33D10Resetting the LampAfter replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:1.Press the Menu button to ope

D10345. trOubleShOOtinGThese guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolve

35D10LED Error MessagesIf there is an error status, the LED remains lit until the AC power cord is removed. An LED message is dened by its blinking s

D1036Common Problems and SolutionsThis section describes some common problems and their solutions.Image ProblemsProblem: No image appears on the scree

37D10Remote Control ProblemsProblem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the p

D10386. SpecificatiOnSHardware SpecicationsMOdel d10Display type TI DMD 0.65-inch x 1, 12 degrees, LVDS DMD with DDP3020Resolution WXGA (1280x768)Col

39D10D10 Projection distance and size table1.53:1Max. Screen Size (Wide)Projection DistanceDiagonal Width Heightm in. m in. m in. m in.1.27 50” 1.11 4

General Safety InformationDo not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, c

D10407. tiMinG MOde tableThe projector can display several resolutions. The following table outlines the resolutions that can be displayed by the proj

41D10Projector DimensionsTop ViewFront ViewNOTEFor ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 1

D10428. reGulatOry cOMplianceFCC WarningThis equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Pa

43D10Downloaded From projector-manual.com Sim2 Manuals

SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - ITALYPhone +39.0434.383.256 • Fax +39.0434.383.260www.sim2.com • e-mail: info@si

Regulatory WarningsBefore installing and using the projector, read the regulatory notices in the “Regulatory Compliance” section 8 on pa

D106Table of Contents1. GettinG StartedPacking Checklist ...

7D101. GettinG StartedPacking ChecklistCarefully unpack the projector and check that the following items are included.DLP Projector Remote Control

D108A Tour of the Projector Front-right ViewiteM label deScriptiOn1 Control panelOperates the onscreen display. Refer to the next page for a descripti

9D10On-screen Display (OSD) ButtonsPower EnterLeftRightMenu InputUpDowniteM label deScriptiOn1 Power Turns the projector on or off2 Left Navigates an